2.830J – Control of Manufacturing Processes MIT OCW

Course Home Page (MIT OCW)

The objective of this subject is to understand the nature of manufacturing process variation and the methods for its control. First, a general process model for control is developed to understand the limitations a specific process places on the type of control used. A general model for process variation is presented and three methods are developed to minimize variations: Statistical Process Control, Process Optimization and in-process Feedback Control. These are considered in a hierarchy of cost-performance tradeoffs, where performance is based on changes in process capability.

1: Introduction — Processes and Variation Framework

Tuesday, January 27, 2009 5:06 AM

Topics covered: Introduction — processes and variation framework

Instructor: Duane Boning, David Hardt

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

2: Semiconductor Process Variation

Tuesday, January 27, 2009 5:06 AM

Topics covered: Semiconductor process variation

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

3: Mechanical Process Variation

Tuesday, January 27, 2009 5:06 AM

Topics covered: Mechanical process variation — physical causes and interpreting data

Instructor: David Hardt

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

4: Probability Models of Manufacturing Processes

Tuesday, January 27, 2009 5:06 AM

Topics covered: Probability models of manufacturing processes

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

5: Probability Models, Parameter Estimation, and Sampling

Tuesday, January 27, 2009 5:06 AM

Topics covered: Probability models, parameter estimation, and sampling

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

6: Sampling Distributions and Statistical Hypotheses

Tuesday, January 27, 2009 5:06 AM

Topics covered: Sampling distributions and statistical hypotheses

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

7: Shewhart SPC and Process Capability

Tuesday, January 27, 2009 5:06 AM

Topics covered: Shewhart SPC and process capability

Instructor: David Hardt

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

8: Process Capability and Alternative SPC Methods

Tuesday, January 27, 2009 5:06 AM

Topics covered: Process capability and alternative SPC methods

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

9: Advanced and Multivariate SPC

Tuesday, January 27, 2009 5:06 AM

Topics covered: Advanced and multivariate SPC

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

10: Yield Modeling

Tuesday, January 27, 2009 5:06 AM

Topics covered: Yield modeling

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

11: Introduction to Analysis of Variance

Tuesday, January 27, 2009 5:06 AM

Topics covered: Introduction to analysis of variance

Instructor: Hayden Taylor

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

12: Full Factorial Models

Tuesday, January 27, 2009 5:06 AM

Topics covered: Full factorial models

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

13: Modeling Testing and Fractional Factorial Models

Tuesday, January 27, 2009 5:06 AM

Topics covered: Modeling testing and fractional factorial models

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

14: Aliasing and Higher Order Models

Tuesday, January 27, 2009 5:06 AM

Topics covered: Aliasing and higher order models

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

15: Response Surface Modeling and Process Optimization

Tuesday, January 27, 2009 5:06 AM

Topics covered: Response surface modeling and process optimization

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

16: Process Robustness

Tuesday, January 27, 2009 5:06 AM

Topics covered: Process robustness

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

17: Nested Variance Components

Tuesday, January 27, 2009 5:06 AM

Topics covered: Nested variance components

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

18: Sequential Experimentation

Tuesday, January 27, 2009 5:06 AM

Topics covered: Sequential experimentation: “Experimentation and Robust Design and Engineering Systems.”

Instructor: Dan Frey

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

19: Case Study 1: Tungsten CVD DOE/RSM

Tuesday, January 27, 2009 5:06 AM

Topics covered: Case study 1: tungsten CVD DOE/RSM

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

20: Case Study 2: Cycle to Cycle Control

Tuesday, January 27, 2009 5:06 AM

Topics covered: Case study 2: cycle to cycle control

Instructor: David Hardt

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

21: Case Study 3: Spatial Modeling

Tuesday, January 27, 2009 5:06 AM

Topics covered: Case study 3: spatial modeling

Instructor: Duane Boning

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

22: Case Study 4: “Modeling the Embossing/Imprinting of Thermoplastic Layers.”

Tuesday, January 27, 2009 5:06 AM

Topics covered: Case study 4: “Modeling the Embossing/Imprinting of Thermoplastic Layers.”

Instructor: Hayden Taylor

Note: The slides used in this lecture can be found at the Lecture Slides tab

 

(CC BY-NC-SA)

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to Top